Not Another Brick Wreath

Designer

NeoRame

Designer relation

Ingen

Kategori

Household

Licens

Standard Digital File License

$ ↺

Se platformens konkrete vilkår.

Designer commercial

MakerWorld Commercial License

Først set

2026-07-14 16:37

Sidst set

2026-07-14 16:37

Tags

brick neorame bricks brickbuilder build Christmas x-mas xmas wreath easter halloween door decoration

Beskrivelse

Important Notice! Please read carefully! After receiving a strike from "Big L," I had to remove the brand… and consequently lost 19,500 points from MakerWorld! No, I cannot recover the files. No, there is no way to obtain or find the old files. Please stop asking! Since November 11, 2025, the pins have a new diameter! 20.1 mm for the pin and for the hole! No, I cannot and will not restore the old diameter! Why? Because this will be the basis for all future parts! Version 1 had incorrect dimensions due to incorrect measurements. The parts are now accurate! All add-on creators must update their files… SORRY. If you have made changes to other add-ons, please contact the respective creators and inform them of the new dimensions. However, I will create an adapter ring from V2 to V1 so that you can also use the new content in older setups. -------------------- Update 8: 3 Dec 2025 THANK YOU SO MUCH FOR ALL YOUR SUPPORT! I'm back to positive balance! And ass a thank you i create a new piece: Twist'n'Lock Pin + Key Some of you called…and now… I deliver!!!! A Locking Pin Only! works on every corner! And come with a Key to open and close as a little Fun Part. -------------------- Update 7: 20 Nov 2025 Add an All in One Hanger (ribbon, screw, nail, tape…) with Twist'n'Lock function. Also “Tile Round 1x1” for Twist'n'Lock. -------------------- Update 6: 11 Nov 2025 Rollout V2!!! Changed the Pin diameter to 20,1mm for stud hole and the pin, to look more Original, i had the wrong sizes. Old Studs and and other parts works with the new parts and vice versa, exept the Pins (Bow and the old Candle) -------------------- Update 5: 11 Oct 2025 Inspired n.polking (original by makewithjakes) Locking Stud i recreate my Mounts. I introduce: Twist'n'Lock Wreath Corner Mount (new Print Profile) the Mount work for the actually Lite Leaf and the upcoming V2 ;) -------------------- Update 4: 02 Oct 2025 It's time for Halloween. You have already printed this Wreath? Print your "Halloween Addon" now to show your spooky side. The Wreath is back! After the takedown i cleaned up the files. No Logos. PURE BRICKS. -------------------- Update 3: Now with Building Instruction as PDF and PNG -------------------- Update 2: Add two new types of hanger. One with screw hole for screws and nails and one with a hanger for ribbons and stuff. -------------------- Update: Some of you wished some candles to place the wreath on the Table as a Advent wreath. Give me the Brick Candle (re-upload comming soon) ---------------------- And here it is my own version of a giant Brick wreath. Why another on? Because, existing one that i tried was: too tight, to loose, not really supportless printable, in wrong proportions and most of it are not really stackable without a gap! This is why i started to create a new one from scratch. Only for the ribbon i used as base an existing model, but i modified it to print it supportless and i widen the pin to fit in standard holes. This model comes also with three 120 degrees angle guides which can use for wall mounting witch "Poster Strips" THE MYSTERY about the Plate #5 and how to use the parts CORRECTLY! Have you seen my other Brick Stuff? ❄️ Not another Brick Snowflake ❄️ 🎄 Not another Brick Wreath 🎄 🕯️ Not another Brick Wreath with (LED) candles 🕯️ 🎃 Halloween Addon for "Not another Brick Wreath" 🎃 Boost Me (for free) If you like my work, feel free and boost me. Like, rate and share your makes with me :) Boost Membership If you want to buy me a coffee monthly... or a beer.... or hot chocolate? Now you can subscribe... too ;) You can here find different commercial print licence, too. Join