Fidget Pumpkin

Designer

makerxdesigns

Designer relation

Ingen

Kategori

Toys & Games

Licens

Creative Commons Attribution NonCommercial NoDerivatives Creative Commons - Attribution - Non-Commercial - No Derivatives

$ ↺

Attribution påkrævet; kommerciel brug og deling af modificerede versioner er ikke tilladt.

Designer commercial

None

Først set

2026-09-17 20:20

Sidst set

2026-09-17 20:20

Tags

desk toy fidget Fidget Toy fidget-toy fidgeting gift halloween Halloween pumpkin happy halloween Makerx makerxdesigns no supports no supports needed no supports required no-supports Printable No Supports requires no supports toy toys

Beskrivelse

The "Keeps Your Hands Busy" Fidget Pumpkin 🎃 A fidget toy for your desk. It sits flat as a pumpkin, and every way you move the stem gives it a different look. 🟩 𝗪𝗔𝗬𝗦 𝗧𝗢 𝗣𝗟𝗔𝗬 ▸ 𝗧𝘄𝗶𝘀𝘁 𝘁𝗵𝗲 𝗦𝘁𝗲𝗺 — Leave it flat on the desk and twist. The rings shift against each other into mesmerizing designs. ▸ 𝗣𝘂𝘀𝗵 𝗮𝗻𝗱 𝗣𝘂𝗹𝗹 — Slide the stem from side to side and the rings ripple off-center for a whole different set of visuals. ▸ 𝗟𝗶𝗳𝘁 𝗜𝘁 𝗨𝗽 — Raise it by the stem and the 18 rings drop into a scalloped cone. ▸ 𝗛𝗲𝗮𝗿 𝗜𝘁 𝗦𝗲𝘁𝘁𝗹𝗲 — Raise and lower it on the desk and it makes a satisfying sound as the rings come back down. ▸ 𝗧𝗲𝘅𝘁𝘂𝗿𝗲𝗱 𝗦𝘁𝗲𝗺 — The stem is textured, so it has a tactile feel under your fingers while you fidget. 🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞 ▸ 𝗣𝗿𝗶𝗻𝘁𝘀 𝗶𝗻 𝗣𝗹𝗮𝗰𝗲 — One print, no assembly. All 18 rings and the stem come off the plate already captured inside each other. ▸ 𝗧𝘂𝗻𝗲𝗱 𝗚𝗮𝗽𝘀 — The gap between rings grows from about 1mm at the stem to about 2mm at the rim, so the outer rings still move freely instead of binding up. ▸ 𝗦𝘁𝗮𝘆𝘀 𝗧𝗼𝗴𝗲𝘁𝗵𝗲𝗿 — The ring walls are angled so each ring stays captured by its neighbors while you twist, slide and lift it. ▸ 𝗧𝗵𝗿𝗲𝗲 𝗖𝗼𝗹𝗼𝗿𝘀, 𝗧𝘄𝗼 𝗦𝘄𝗮𝗽𝘀 — Black ring bodies, orange faces and a brown stem, for only two filament changes and under 3g of purge. 🟩 𝗖𝗛𝗘𝗖𝗞 𝗬𝗢𝗨𝗥 𝗕𝗘𝗗 𝗙𝗜𝗥𝗦𝗧 ▸ 179 x 174mm across and 45mm tall with the stem. Leave room beside it for the prime tower if you print it in color. 🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦 No supports required · no brim · 0.20mm layer height · 2 walls · 10% grid infill · PLA Printed on a Creality Hi 2 in 5h 2m and 127g. Happy fidgeting! 🎃